Exactly How to Remove and Change a Bathtub
Exactly How to Remove and Change a Bathtub
Blog Article
Just about every person seems to have their personal way of thinking in relation to How to Install a Bathtub.
Mounting a bathtub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and also sometimes, tiling abilities. Replacing an old tub with a new one is likewise a moderately tough job. If the old tub is easily accessible, the job can relocate rapidly; if you need to open a wall surface to remove the old bathtub and also position the brand-new bathtub, the job is much harder. In either situation, the task is within a residence handyman's abilities, although you will certainly need a helper to vacate the old tub as well as embeded in the new one. Make certain you have qualified on your own for the work and fit trying it. Rather than employing a service provider to take over a halfway-completed job, it is much better to consider employing one before you start. Opportunities are you may need an expert plumber to make tube links.
This article will assist you install a new bathtub in your shower room if you have already purchased a brand-new bathtub and do not require to transform the arrangement of your previous water pipelines.
Your tools as well as product checklist ought to make up the following:
Getting ready for the Setup
First of all, the sustaining frame provided with the bath ought to be fitted (if called for) according to the supplier's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to avoid stress on the bathtub.
Fit the adaptable faucet ports to the bottom of the two taps making use of 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you make use of every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should now be ready to be fitted in its last placement.
Removing Old Touches
If you need to replace old taps with new ones as a part of your setup, after that the first thing you must do is separate the water. After doing so, activate the faucets to drain pipes any water continuing to be in the system. The process of removing the existing taps can be rather troublesome as a result of the limited accessibility that is typically the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the faucets. Have a fabric ready for the staying water that will certainly originate from the pipelines. Once the supply pipes have been removed, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. When the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new faucets to fit.
Mounting the Tub
Making use of both wooden boards under its feet, put the bath tub in the required position. The wood boards are helpful in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four small factors.
The next objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the level and changing the feet on the tub till the spirit level checks out degree.
To install faucets, fit all-time low of the furthest versatile faucet connector to the proper supply pipeline by making a compression join; then do the very same for the other tap.
Activate the water supply and inspect all joints and also new pipework for leaks and also tighten them if necessary. Load the bathtub and likewise examine the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bathtub ought to wait up until the tub has actually been made use of at the very least when as this will settle it into its final setting.
Suitable New Touches
If the tails of the new taps are plastic, then you will need a plastic port to stop damages to the string. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin ensuring that the washing machines are in place between the tap and the sink. Secure the tap in position with the manufacturer provided backnut. Once the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet ports. The previous type ought to be linked to the tap ends first, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to crack a stiff seal, triggering the water to permeate the wall between the bathroom as well as the tiling, resulting in problems with wetness as well as possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and installations. They are offered in tubes and cartridges, and can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly fill the bathtub with water before securing, to enable the motion experienced when the bathtub remains in use. The sealant can crack relatively early if you do not take into account this movement prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also quickly offered on the marketplace. It is suggested to fit the tiles using waterproof or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate reading up on How to Install a Bathtub? Give a remark down the page. We'd be interested to know your thoughts about this piece. Hoping that you come back again in the near future. Appreciated our blog entry? Please share it. Let others locate it. I thank you for reading our article about A Step-by-Step Guide to Installing a Bathtub.
Get Started
Report this page